EP model substitution gearbox for woods rotary gearbox
NEW forty HP GEARBOX Clean Input 1 3/8 twelve spline output Interchangable with industry popular measurement i.e.: OMNI GRIZZLEY CHEETAH HOWSE KING KUTTER BUSH HOG HICO SILVER EDGE Several Far more
Features
(one) manufacturer new forty five horse energy shearpin gearbox. This gearbox suits a number of various can make of 4′,5′ and some 6′ rotary cutters. I promote a whole lot of these bins each and every year for numerous diverse apps and carry ALL Replacement Components for this box, but with any luck , you will not have to worry about that.
Here are the specs on the box:
*45 horse electrical power gearbox
*Common 1-3/8″ sleek enter shaft(where the pto shaft hooks on). The pto shaft is held on by a 1/two shearbolt.
*length of the input shaft out of the gearbox is three” lengthy
*bolt gap pattern for mounting is on the corners, 4-3/4 heart of gap to centre of hole. It will take a five/8″ bolt.
*12 splined output shaft(where the blade provider hooks up on the bottom)
*one-nine/16 outside the house measurement over the output shaft splines- from the base of the output cap to the conclude of the splines is 2-3/4″ prolonged- overall size of the output shaft is four-1/2″ extended.
*takes a one” threaded castle nut and a carter key on the base of the output shaft to protected blade pan(NUT is integrated – – BLADE PAN IS NOT!!)
*total height of the box from the top of the mower deck to the leading of the box is 9-1/2″
This is a pretty large merchandise (forty seven lbs.) so freight is not low cost, but we do not make something off of freight, what ever ups costs us we cost you.
40 HP
one:one:forty seven Ratio
1-3/eight” Sleek Enter Shaft with Shear Pin Hole
1-1/2″ 12-Spline Ouput Shaft
Bolt Sample: 6-1/two” (4) 5/8″ Holes, 5″ Center Hole Necessary for Shaft Assembly
The Input and Output Shafts Can not be Obtained Serparately.
They are Offered as a kit.
The kit consists of the following components: enter shaft, input gear, output shaft, output equipment.
The Shaft Package Can not Be Divided.
EP manufacturer substitute gearbox for woods rotary gearbox
Rotary Cutter Gearbox Troubleshooting Information
Is your mower leaking, creaking or or else doing incorrectly? You have come to the right place.
Study beneath for the most widespread problems with rotary cutter gearboxes and their answers (from swift and filthy, to specialist).
Leaking Bottom Seal:
If you’ve wrapped some baling or fencing wire close to your output shaft and blown the seal, the specialist issue to do is to change the seal.
If your output seal is intact, and you are able to get ID, OD and thickness measurements (in millimeters), most bearing properties can get you up a generic double-lip seal that will get you back again up-and-working. If not, give us a call and we can help you form out what you want.
A dental choose is the simplest way to eliminate the outdated seal 
prior to pressing in the new 1.
If you might be fortunate enough to have a sluggish-leak, the fast and soiled technique is to operate automotive-kind grease in the gearbox right up until the new seal will come in. Be positive to verify and insert grease a lot more often than you would with oil, as this is NOT a skilled mend.
Damaged Output Shaft:
Uh oh. You strike some thing that didn’t go. The very good news is that the output shaft on most gearboxes is relatively easy to change. The bad news is… it truly is hardly ever an isolated failure.
The very first factor to do is to get aside your gearbox and assess the total extent of the damage. If it is truly just the output shaft, you should be in a position to alter it out, no difficulty. The output shafts start at about $70 and go up in price based on the dimension of the gearbox.
Nevertheless, in most situations, the bearings ($20/ea), seals ($ten/ea) and equipment-set ($70) will also usually take a beating. If you happen to be unfortunate, the output cap ($eighty) will also experience some hurt.
In this scenario, it is generally more affordable to replace the gearbox. Evaluate the cost of elements to the value of an total, new, warrantied gearbox. At times, even professionals have to know when to contact it a day.
I Want to Change my Enter Shaft:
If you are fatigued of changing shear pins or seeking again and looking at that your mower hasn’t been slicing, you may possibly want to set up a slip-clutch pto shaft (Sure, we offer these as well).
This normally demands setting up a 540-design, six-spline input shaft ($eighty five) on your mower’s gearbox.
Blessed for you, we did a compose-up on our blog. It’s known as “How to adjust the input shaft on your rotary cutter gearbox”.
My Gearbox is Groaning/Creaking:
“Groaning”, “creaking”, or “popping” all sound kind-of comparable above-the-mobile phone. The very best thing to do is to disassemble your gearbox and consider a seem at the gears and bearings. The concern will usually present alone in the way of broken/missing equipment teeth, toasted gears (like that image on our home page), or blown bearings.
If everything looks typical, consider changing the gear-mesh. This is completed with the mylar “gaskets” that sit among the main gearbox case and the input/output caps. Consider including or taking away some of these spacers until finally your gears have approximately one/8″-1/four” of free perform. Professionals can get replacements ($1-two) in different thicknesses, but we recommend the fast and soiled method of slicing your own out of a sheet of mylar.
Never fail to remember to re-seal the gearbox with RTV following you’ve got found the correct mixture. Even though they’re called “gaskets”, they will not seal your gearbox on their very own.
Right here at http://agricultural-gearbox.xyz/agricultural-gearbox/gearbox-reducer-for-climate-screens-drive.html we are quite severe about our Gearbox for Agricultural Machinery.